Back to top

Problems you may encounter when operating a wood planer

Woodworking and sculpture are still preserved and developed as well as other professions. The expansion of the wood industry, followed by the development of woodworking machines, especially the wood planer that is an indispensable tool and an effective assistant to help carpenters easily flatten. , smooth wooden panels, thereby creating exquisite, beautiful products in today’s furniture manufacturing.

However, The best wood planer usually works with high performance and under high pressure. Consequently, when used for a long time, unfortunate incidents and failures are likely evident. And this not only makes it difficult for people to work, but it can also cause unnecessary risks.

Therefore, Questions about how to avoid errors and minimize the damage and harm caused by operating a wood planer are of more interest and attention.

In this article, I pointed out some common problems when using the cutters that you can refer to if you encounter them, you know how to handle them.

The ac motor does not start in the planer

Improper installation of wood planers is the cause of the motor from the power does not work. The circuit is assembled incorrectly, the power supply is not stable or the electric wire is too small to load the electricity leads to making the planer motor unable to start.

In case of touching masse due to the main short-circuiting, it opens the main winding circuit, the coil in 1-phase electric motor makes the combination lose. It can be determined using a VOM meter.

Affecting the masse will cause electric shock, when the engine may explode and lead to masse touch. Now, please check whether the engine is peeling or not. If yes, it should be repaired promptly.

When you hold the planer, the power shakes slightly in case of a slight shock. The cause is because the engine is contaminated with moisture, it needs to be dried. In the case of a strong electric shock, you must quickly bring it to a repair center for timely warranty.

The electric motor in the planer generates heat too quickly

The reason is that by affecting the phase coils, making the engine to heat rapidly and smoke may be emitted.

If this situation is maintained for a long time, the motor will be reduced and the buzzing will be generated, resulting in reduced productivity.

When the engine starts to pull the mass, the speed decreases, the heat creates, which leads to the case that the pressure is not pulled due to a sudden increase in the phase of the motor.

Wood planing motor when running, sometimes not

In many instances, the wood planer is suddenly stopped, resulting in an incomplete product. At this time, users need to check the power supply in the motor, whether the plugs are loose or not. Or the circuit breakers are working properly, the power supply CBs, screw joints are loose or not.

These problems require to be repaired in time because a sudden power outage will cause the planing machine to be interrupted. The engine that is operating but suddenly shut down will easily lead to an engine fire.

Or need to check the connectors and joints in the motor winding, the welding joints are also the cause of the motor of the wood planing device flickering, directly affecting the service life of the wood planer.

The heat generation is too hot when the engine is operating

This not only affects the motor but can also cause injury to the user, the main reason is:

  • Operation is suddenly lost phase.
  • The rotor motor is touched by the stator, which generates heat locally.
  • The power supply is not sufficient with the rated voltage.
  • Ventilation holes in the electric motor of the planing machine do not work.
  • Due to the incorrect assembly order of the machine’s parts, leading to an increase in unnecessary resistance to the engine of the machine when operating also generates heat.

The planer motor has the hum and the speed is not high

Due to insufficient power supply voltage will cause power interruption or short circuit in the engine is reduced to make a buzzing sound.

In conclusion

Above are some common errors in the operation of the wood planing device as well as the best thickness planer. Hopefully, this information will help you take note and make better use of your wood planer. And thank you for taking the time to read this article

How to locate leaks with a moisture meter

The leakage of structure in building materials from an office or a house is not new problem. In fact, you suddenly see the walls or ceiling of your home getting wet. That is not difficult to explain.These are obvious signs of a leak. Your wall has leaked in its structure.

However, finding a leak quickly is important. Because leaks not only add to the cost of water bills, the damage caused by water entering the structure can also require you to spend thousands of dollars on restoration and repair.

For many common leaks, finding and fixing the source of the problem is relatively easy. For example, if your faucet or shower is leaking, you may just require to tighten or replace a new one to repair this problem. Because the source of the leakage is in clear vision. However, not all leaks occur in simple, accessible or visible spots. Sometimes, water ingress occurs in places that you cannot see directly, such as behind walls or on ceilings, where visible signs of leakage may not appear immediately

To solve this difficult problem, manufacturers have invented a hygrometer. It is a very useful tool for detecting moisture in building materials and for identifying leaks in structures, even if the origin can be out of sight. This is why the hygrometer has quickly become an important and indispensable tool for water damage repair professionals or contractors.

How can you locate a leak with a hygrometer? Many of you have asked this question, right? In this article, I will give some tips on how to locate a leak when using a hygrometer. Let’s start reading and find out.

moisture-meters
moisture-meters

How to locate leaks in walls, dry plaster, bricks and concrete

Construction materials like dry plaster, bricks, and concrete usually have very little moisture in them.

However, when they leak, it is difficult to identify and place. So, how to solve this problem? Let’s get yourself a hygrometer. It helps you to discover most of those leaked locations.

Find out how to find out where it leaks now. You will require the following:

To start locating a leak, you need to set the gauge in an area of building material that you know is wet. Then, attach the insulated wire to the foundation and one of the hygrometer contact pins. When the cord is connected to one of the contact pins, apply the other pin to different parts of the material where you suspect a leak might be coming from. The battery moisture meter gives a “wet” result, the wall gets wet between the two contact points. If the battery meter shows a “dry” response, the material is not in the leak. Continue testing with other locations until you determine the leak area limit.

This procedure will help you determine the location of a leak using a hygrometer when examining building materials to ensure that the materials are in their best condition.

Find leakage on the insulating material

When the loose insulation gets wet, the moisture not only damages the building’s thermal stability, it also becomes a potential hiding place for mold. Over time, the moisture retained in the insulation will begin to affect the structures that the insulation is exposed to and cause damage.

To test the insulation, you will need to use a hygrometer with extended length probes. Because only the ends of these pins are exposed, you can easily determine the depth of insulation in an insulated bag. You don’t have to tear down the entire wall to get the insulation to start the test, you just require to drill two 3/16 diameter holes and install it an inch apart in the outer or plaster walls of your home to measure.

Once the holes have been drilled, push the pins into the holes and start reading at different depths using the reference ratio setting of your battery meter. Setting the reference rate will give you a relatively accurate assessment of any moisture present in the material measured. When you have finished reading the moisture, seal the holes drilled with suitable fillers.

Especially in cold weather, water vapor in the air will condense, which causes moisture to rise rapidly. Moreover, It causes the steam to be trapped in the insulation of the material. Therefore, you should check the humidity regularly

In conclusion

By locating a leak with a hygrometer, you can save time and money for plumber or restoration specialist to know where the leak is coming from. The less time they seek a leak to repair water damage, the lower your labor costs will be. It is extremely useful, isn’t it? Let’s consider and purchase the best moisture meter for your family right away. Finally, hope the article is helpful for you and thank you for taking the time to read.

Wish List: Outfit for a Zen Workout

I’m not a New Year’s Resolution type of girl. Never have been. However, January really does feel like a good time to re-dedicate myself to one of my true loves: working out. My very first job, where I actually got a paycheck, was at a gym. I feel really comfortable at a gym. I’m not one of those gym rats, who hang out all day and chit chat. In fact, I’ve been going to my current gym for about six months and have yet to say more than about 10 words to anyone. I like solitude in my workouts. One of the things that annoys me the most in life is people who talk during workout classes. My favorite workout used to be swimming (go figure) but these days I just don’t have the time. My mom introduced me to spin classes, and I’m hooked. Although it’s a class environment, it’s truly a solitary type of feeling I get in that class. I usually close my eyes during much of the workout, so it’s peaceful, like swimming.

Here are a few items on my wish list … things that would make my workout a little more chic, a little more comfy, a little more cool: Green jacket from Athleta; Shimano cycle shoes from Zappos; cute graphic grey tank top from Old Navy; capri workout pants from Old Navy; ta ta tamer bra from lululemon; and a pretty AND functional water bottle with filter right in it by Bobble (designed by Karim Rashid) from A+R Store.